#Program liftmaster keypad instructions install#

Install a screw into the top drilled hole, leaving a 1/8' gap between the screw head and the wall.

The garage door / gate opener must be programmed to accept the new keypad code. Reattach the faceplate to the mounting plate and lock with the key. Connect the white battery connector to the PCBA (see illustration) and reinstall the cover.

Drill a 1/16' hole for the top mounting screw. Remove the battery cover using a screw driver.

If the red LED does not blink during use, the battery needs to be changed.

After a few seconds, the LED will turn off, and you can retry.

Rapid blinking of the LED indicates an error.

Any keypad button will control the door for 30 seconds after the door starts moving.

If the LED blinks rapidly, the PIN was entered incorrectly.

If the garage door does not move, check the red LED on the keypad.

Otherwise, you have to restart the process. The programming is complete if the flashing LED icon stops and the garage door opener operates. Each door opener must be programmed to receive the signal from the wireless keypad. Once your garage door opener’s Program Mode is enabled, press and hold the selected button for about 10 seconds until the LED icon flashes.

Repeat steps one through five for programming each garage door opener.

Press and hold the Learn button on garage door opener or other product.

Press the arrow up/down triangle button a third time. When deactivating any unwanted remote control code, all previous codes will be erased.

Press the arrow up/down triangle button a second time.

Press the number you have picked for this door opener: 1, 2 or 3.

“Learn Code” indicator LED continues to blink.

Enter your PIN and press the arrow up/down triangle button.

“Learn Code” indicator LED (on opener) blinks.

Decide which door will be Door 1, 2 and 3.

Press the PROG button a third time (red LED blinks several times and turns off).

Press the total number of doors you wish to control (either 2 or 3).

The LED will flash.Enter a 4-digit PIN of your choice on the keypad, and press ENTER.The opener lights will blink, indicating the PIN programming is.

#Program liftmaster keypad instructions how to#

Press the PROG button a second time (red LED blinks twice per second). How to Program a Garage Door Keypad PIN Using Your Door Control Be sure to clear the garage door area of any obstructions.Locate the LEARN button on the door control.Press the LEARN button twice.Press and release the Learn Button on the garage door opener motor. Enter your PIN and press the PROG button (red LED blinks once per second). On the keypad press and hold the and buttons until the keypad lights stop flashing.Programming Two Or Three Garage Door OpenersĪll garage door openers will use the same PIN. Press the button with the arrow up/down triangles a third time.The “Learn Code” indicator LED will turn off. Press the button with the arrow up/down triangles a second time.

The “Learn Code” indicator LED will stay on. Press the button with the arrow up/down triangles.Press the “Learn Code” button once (red LED indicator will blink).Locate the “Learn Code” button and the “Learn Code” red LED indicator. Press the PROG key again (red LED blinks twice per second and turns off).īefore you begin, be aware of the following:įor convenience, program your keypad before mounting.If programming your garage door opener is disrupted at any point due to program failure, clear/reset your keypad.Enter your PIN (three to eight characters).Press the following keys in order: 3, 5, 7, PROG (red LED blinks once per second).Press the key with the arrow up/down triangles. HOW TO PROGRAM A STANDARD LIFTMASTER REMOTE CONTROL Locate the Learn button on your garage door opener.Enter your personal identification number (PIN).Security+2.Basic Instructions Testing Garage Door Opener.Plus, it works with all LiftMaster® garage door openers manufactured since January 1993. You can also program it with temporary access codes for visitors or delivery and service personnel so they can gain access to your garage without having to give them your personal code.

#Program liftmaster keypad instructions code#

The 878MAX LiftMaster® Wireless Keyless Entry System can open the door using a private 4-digit code you program directly into the unit. Open or close your garage door without using a remote control or key. These instructions cover the Liftmaster 878MAX Wireless Keyless Entry System (replaces previous model 877MAX)